国产在线高清视频-国产在线观看不卡免费高清-国产在线观看成人-国产在线观看成人免费视频-亚洲成人看片-亚洲成人毛片

CN EN
Company News
Home > Company News

The relationship between blanking gap and shear quality

Source:Suzhou Meiyuan Ruite Precision Machinery Co., Ltd. Time:2022-06-16 Browse:2835


Whether the blanking gap in the blanking process is reasonable will determine whether the upper and lower cracks on the fracture surface overlap, whether the shear force is balanced, and the size of the burr. Therefore, the mold design, manufacture and installation must ensure that the gap is uniform, and the gap between the convex and concave molds in the same manufacturing process should be kept within a reasonable range. Otherwise, the mold will appear part of the gap is too large and too small quality phenomenon.​​
 
Effect of Gap on Section Quality
1. Reasonable blanking gap
When the convex and concave gaps are appropriate, the cracks generated near the edges of the convex and concave die along the direction of the maximum shear stress can meet during the blanking process. At this time, although the section is not perpendicular to the surface of the material, it is still relatively straight, smooth and burr Smaller, the section quality of the part is better.
 
2. Punching gap is too small
When the gap is reduced, the bending moment is small and the compressive stress component is high in the deformation zone. The cracks generated near the edge of the die enter the compressive stress zone below the punch and stop developing; the cracks generated near the edge of the punch enter the compressive stress zone on the upper surface of the die and stop developing. The upper and lower cracks do not overlap. The material between the two cracks will be sheared a second time. When the upper crack is pressed into the die, it is squeezed by the wall of the die, resulting in a second bright band, and at the same time, part of the material is extruded, forming thin and high burrs on the surface. If the gap is too small, although the slump angle is small and the arch is small, the quality of the section is also defective. If there is an interlayer in the middle of the section, the two ends are bright bands, and there are long burrs on the end face.
 
3. Punching gap is too large
When the gap increases, the tensile stress in the material increases, so that the tensile fracture occurs early, so the fracture band becomes wider; the bright band becomes narrower; the bending deformation increases, so the slump and arch also increase. When the gap is too large, due to the large bending moment and the high tensile stress component, the cracks generated near the edges of the convex and concave molds will not coincide. The slope of the fractured layer generated after separation increases, and two oblique angles α1 and α2 appear on the section of the workpiece, and the section quality is not ideal. Moreover, due to the large slump angle, the large arch, the small bright band, and the high and thick burrs, the quality of the blanking parts is reduced.
 
4. The gap is uneven
The side with a small gap presents the cross-sectional feature of an excessively small gap, and the side with a large gap presents the cross-sectional feature of an excessively large gap


主站蜘蛛池模板: 天天爱天天做天天爽| 天堂bt资源www在线| 天天综合网网欲色| 手机看片自拍| 福利片网站| 日韩一级欧美一级| 伊人狠狠丁香婷婷综合色| 日韩亚洲人成在线综合日本| 人人干国产| 亚洲综合黄色| www.色婷婷| 狠狠色丁香婷婷综合橹不卡| 欧美综合成人网| 亚洲v视频| aaa视频| 91色在线视频| 久久亚洲视频| 美女涩涩网站| 免费国产网站| 欧美成人69| 日本黄色影片| 视频二区在线观看| 欧美性受xxxx| 国产精品久久久久久影院| 男人资源| 黄色网址中文字幕| 久久久国产精品免费| 国模娜娜扒开嫩木耳| 免费观看国产网址你懂的| 在线另类| 热九九精品| 日xxxx| 一级做a爰片久久毛片毛片| 色视频在线免费看| 四虎影在线永久免费观看| 四虎永久精品视频在线| 九色中文| 丁香花在线视频观看免费| www伊人| 亚洲丁香网| 日日操天天操夜夜操|